Manual Makita UH550D Corta-sebes

Manual

11

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Battery adapter (Accessory) (Fig. 6 & 7)

CAUTION:

• Before using battery adapter, read all instructions on

tools using battery.

• When charging a battery cartridge, first remove it from

the battery adapter and then charge it. It is not allowed

to charge the battery cartridge while using battery

adapter.

Installing or removing battery adapter

• Always switch off the tool before insertion or removal of

the battery adapter.

• To remove the battery adapter, withdraw it from the tool

while sliding the button on the adapter.

• To insert the battery adapter, align the tongue on the

battery adapter with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery adapter. If

the adapter does not slide in easily, it is not being

inserted correctly.

• The way of removing or installing a battery cartridge

from or on the battery adapter is the same as that of

removing or installing it from or on the tools.

• Press down the hook securely as far as it will go when

the battery adapter is hooked on the waist belt and

similar objects.

Arm cord hook (Accessory)

CAUTION:

• Do not attach the holder of arm cord hook to other than

the extension cord. Failure to do so may cause an

accident or personal injury.

Using the arm cord hook helps to minimize a risk of

cutting off the extension cord unexpectedly caused by the

loose extension cord. (Fig. 8)

Attach firmly the arm cord hook band placing around your

arm and pass the extension cord through the holder.

The length of the arm cord hook band is adjustable.

NOTE:

• Do not pass the extension cord through the band.

• Do not force the opening of the holder. Failure to do so

may cause deflection and damage to it.

OPERATION

CAUTION:

• Be careful not to accidentally contact a metal fence or

other hard objects while trimming. The blade will break

and may cause serious injury.

• Overreaching with a hedge trimmer, particularly from a

ladder, is extremely dangerous. Do not work from

anything wobbly or infirm. (Fig. 9)

Do not attempt to cut branches thicker than 10 mm

diameter with this trimmer. These should first be cut with

shears down to the hedge trimming level.

CAUTION:

• Do not cut off dead trees or similar hard objects.

Failure to do so may damage the tool. (Fig. 10)

Hold the trimmer with both hands and pull the switch

trigger A or B and then move it in front of your body.

(Fig. 11)

As a basic operation, tilt the blades towards the trimming

direction and move it calmly and slowly at the speed rate

of 3 - 4 seconds per meter. (Fig. 12)

To cut a hedge top evenly, it helps to tie a string at the

desired hedge height and to trim along it, using it as a

reference line. (Fig. 13)

Attaching the chip receiver (accessory) on the tool when

trimming the hedge straight can avoid cut off leaves’ being

thrown away. (Fig. 14)

Rotate the handle for your easy handling before

operation. Refer to the section titled “Handle mounting

position”.

To cut a hedge side evenly, it helps to cut from the bottom

upwards. (Fig. 15)

Trim boxwood or rhododendron from the base toward the

top for a nice appearance and good job.

Installing or removing chip receiver

(accessory)

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing chip receiver.

NOTE:

• When replacing the chip receiver, always wear gloves

so that hands and face does not directly contact the

blade. Failure to do so may cause personal injury.

• Always be sure to remove the blade cover before

installing the chip receiver.

• The chip receiver receives cut-off leaves and alleviates

collecting thrown-away leaves. This can be installed on

either side of the tool. (Fig. 16)

Press the chip receiver on the shear blades so that its slits

overlap with the nuts on the shear blades. At this time,

make sure that the chip receiver does not contact branch

catcher at the top of the shear blades. (Fig. 17)

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita UH550D Corta-sebes. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita UH550D Corta-sebes em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Corta-sebes
Mais manuais de Corta-sebes

Perguntas frequentes sobre Makita UH550D Corta-sebes

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Makita UH007GZ Corta-sebes

Manual

Makita UH009GM201 Corta-sebes

Manual

Makita DUN500WZ Corta-sebes

Manual

Makita DUH752Z Corta-sebes

Manual

Makita UH007GD201 Corta-sebes

Manual

Makita UH4860 Corta-sebes

Manual

Makita UH005GZ Corta-sebes

Manual

Makita DUH501Z Corta-sebes

Categorias relacionadas