Manual Makita UH550D Corta-sebes

Manual

12

At this time, the chip receiver needs to be installed so that

its hooks fit into grooves in the shear blade unit. (Fig. 18)

To remove the chip receiver, press its lever on both sides

so that the hooks are unlocked. (Fig. 19)

CAUTION:

• The blade cover (standard equipment) cannot be

installed on the tool with the chip receiver being

installed. Before carrying or storing, uninstall the chip

receiver and then install the blade cover to avoid blade

exposure.

NOTE:

• Check the chip receiver for secure installment before

use.

• Never try to uninstall the chip receiver by an excessive

force with its hooks locked in the blade unit grooves.

Using the excessive force may damage it.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Blade maintenance

Smear the blade before and once per hour during

operation using machine oil or similars.

NOTE:

• Before smearing the blade, remove the chip receiver.

After operation, remove dust from both sides of the blade

with wired brush, wipe off it with a rag and then apply

enough low-viscosity oil, such as machine oil etc. and

spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so may

cause rust or damage on the tool.

Removing or installing shear blade

CAUTION:

• Before removing or installing shear blade, always be

sure that the tool is switched off and the battery

cartridge is removed.

• When replacing the shear blade, always wear gloves

without removing blade cover so that hands and face

does not directly contact the blade. Failure to do so

may cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

• For specific way of removing and installing shear

blades refer to the reverse of a package for accessory

shear blades.

Removing the shear blades

Reverse the tool and loosen four screws. (Fig. 20)

NOTE:

• Be careful not to get your hands dirty as grease is

applied in the shear blade driving area.

Remove the under cover. (Fig. 21)

Remove the plate. (Fig. 22)

Set the crank at the angle as shown in the figure with a

slotted bit screwdriver. (Fig. 23)

Remove two screws from the shear blades and the shear

blade unit will be taken out. (Fig. 24)

CAUTION:

• Return the gear to the original position in such a

manner as it was installed if it should be taken away by

mistake.

Installing the shear blade

Prepare 4 removed screws (For under cover), 2 screws

(For shear blade), plate, under cover, and new shear

blades.

Adjust the crank position as shown in the figure. At this

time, apply some grease provided with new shear blades

to the periphery of the crank. (Fig. 25)

Overlap the oval hole in the upper blade with that in the

lower one. (Fig. 26)

Take out the blade cover from the old shear blades and fit

it onto the new ones for easy handling during the

replacement of blades. (Fig. 27)

Place the new shear blades on the tool so that the oval

holes in the shear blades fit onto the crank. Overlap the

holes in the shear blades with the screw holes in the tool

and then secure them with two screws. (Fig. 28)

Check the crank for smooth turn with a slotted bit

screwdriver. (Fig. 29)

Install the plate, under cover on the tool. Tighten the

screw firmly.

NOTE:

• There is no distinction between the top and bottom of

the plate.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades does not operate properly,

there is a poor fit between the blades and crank. Redo

from the beginning.

Replacing carbon brushes (Fig. 30)

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 31)

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it up.

(Fig. 32)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

Reinstall the holder cap cover on the tool.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita UH550D Corta-sebes. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita UH550D Corta-sebes em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Corta-sebes
Mais manuais de Corta-sebes

Perguntas frequentes sobre Makita UH550D Corta-sebes

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Makita UH007GZ Corta-sebes

Manual

Makita UH009GM201 Corta-sebes

Manual

Makita DUN500WZ Corta-sebes

Manual

Makita DUH752Z Corta-sebes

Manual

Makita UH007GD201 Corta-sebes

Manual

Makita UH4860 Corta-sebes

Manual

Makita UH005GZ Corta-sebes

Manual

Makita DUH501Z Corta-sebes

Categorias relacionadas