Manual Makita UH550D Corta-sebes

Manual

10

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury. (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Handle mounting positions (Fig. 2)

The handle can be rotated to either 90° left or right and

mounted either 45° or 90° position to fit your work needs.

First, pull the knob and rotate the handle clockwise or

counterclockwise in the direction of arrow as shown in the

figure. The handle will be locked in 45° position. The pull

the knob and rotate more. The handle will be locked in 90°

position.

CAUTION:

• Always make sure that the handle is locked in the

desired position before operation.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released. (Fig. 3)

For your safety, this tool is equipped with a dual switching

system. To turn on the tool, press triggers A and B.

Release either one of the two pressed triggers to turn off.

The sequence of switching is unimportant as the tool only

starts when both switches are activated.

Speed change (Fig. 4)

The strokes per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 6 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the strokes per

minute.

CAUTION:

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

• The strokes per minute vary by the conditions of

battery cartridge and shear blades.

Battery protection system

The tool is equipped with the protection system, which

automatically cuts off the output power for its long service

life.

The tool may stop during operation when the tool and/or

battery are placed under the following situation. This is

caused by the activation of protection system and does

not show the tool trouble.

• When the tool is overloaded:

At this time, release the switch trigger and remove

causes of overload and then pull the switch trigger

again to restart. When the tool does not work even

after pulling the switch trigger, the battery power

auto-stop is still at work. Charge the battery cartridge

before use.

• When the remaining battery capacity becomes low:

Recharge the battery cartridge.

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 5)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

Number on adjusting dial Strokes per minute (min

-1

)

6 1,800

5 1,750

4 1,650

3 1,500

2 1,300

1 1,000

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may have

malfunctioned.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita UH550D Corta-sebes. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita UH550D Corta-sebes em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Corta-sebes
Mais manuais de Corta-sebes

Perguntas frequentes sobre Makita UH550D Corta-sebes

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Makita UH007GZ Corta-sebes

Manual

Makita UH009GM201 Corta-sebes

Manual

Makita DUN500WZ Corta-sebes

Manual

Makita DUH752Z Corta-sebes

Manual

Makita UH007GD201 Corta-sebes

Manual

Makita UH4860 Corta-sebes

Manual

Makita UH005GZ Corta-sebes

Manual

Makita DUH501Z Corta-sebes

Categorias relacionadas