Manual Sammic V-410 T Máquina vácuo

Manual

alcohol, solvent or glass-cleaners since

they can affect the mechanical properties

of the material and break it. If you

appreciate a crack in the cover, stop the

machine and call the authorised technical

service for repairs; there is a risk of cover

breaking.

-In the event the power cable should get

damaged and have to be replaced, the

repair may only be done by a SAMMIC

approved assistance service.

-Before cleaning, repairing or checking the

machine, you must unplug the machine

from the mains.

-The noise level of a machine in operation,

as measured at a height of 1.6m and a

distance of 1 metre, is 75 dB(A).

Background noise: 32 dB(A).

Oil change

The oil level must be checked weekly. It

should not be below 3/4 of the oil

indicator. Complete the level, if necessary.

Oil must be changed after the first 100

working hours. Afterwards, change oil

every 500 working hours approximately or

at least every 6 months, as well as each

time oil is found to be emulsified. The

accumulated working hours are displayed

when the machine is switched on. To

change oil, unscrew the draining plug and

let the used oil drain out. To fill the pump

with oil, follow the instructions given in the

relevant section.

On pumps with outputs from 40m³/h

upwards, replace the oil filter at the same

time. This filter is of the type used in cars,

as per ref: AWS2, thread 3/4.

The exhaust filtre must be changed every 4

oil changes or on detecting either oil leaks

or oil mist at the escape.

On turning on the machine when the pump

has been working for a total of 500 hours,

the indicator will display 50 and will be

flashing for 10 seconds, indicating that oil

must be changed. During this lapse of

time, the machine will not start, even if the

cover is lowered.

Once oil has been changed, reset the pump

working time according to the following

sequence:

-With the cover open, press STOP. The

vacuum pump will start.

-Lower the cover. The machine will start

and perform a normal cycle.

-Once the vacuum process has started,

press the STOP button quickly. At this

moment, the working time has been reset

to 0. Allow the machine to complete the

cycle.

-Switch the machine off and on, to check

that the working hour display shows 0.

CHANGE OF CONFIGURATION AND

TESTING OF FUNCTIONS

There are three possible configurations of

the electronic board, according to the

machine in which it is fitted.

Configuration "0": Continuous duty, self-

standing machines (V-641 and V-821).

The pump remains on as from the time the

main switch is pressed. This configuration

is intended for machines to be installed in

cold rooms and refrigerating chambers.

Because the pump is on continuously, the

machine is kept hot, which guarantees its

proper operation.

Configuration "1": Discontinued duty, self-

standing machines (V-641 and V-821).

The pump is on only during the vacuuming

and sealing stages.

Configuration "2": Discontinued duty,

desktop machines (V-204, V-253, V-410,

V-421 and V-426). The pump is on only

during the vacuuming stage.

In order to change the machine

configuration, follow the procedure

described below:

WARNING!

The electronic board is fed at 230V, so care

must be taken thorughout the machine

configuration changing and testing

process.

1- Take off the control panel by removing

its 6 front fixing screws and then

remove the cover protecting the

electronic circuit.

2- Press the general switch.

3- Locate two lugs near the word "TEST" on

the electronic board and short-circuit

them with a screwdriver or similar

object. At this moment, the test process

starts: the electronic board activates

each output (Motor, Sealing solenoid

valve, etc.) for one (1) second and its

associated LED on the board should

then turn on. Next to each LED, there is

a text identifying the component being

tested.

4- On completion of the test sequence, the

display indicates the machine

configuration. If you press STOP at this

stage, the pump working time counter

will be zero-reset.

5- In order to change the machine

configuration, press the Incrementer or

Decrementer key until the required

configuration value is shown.

6- To exit the test mode and save the new

configuration, switch the machine off. If

you lower the cover before exiting the

test mode, the machine will not start. In

the event that the working time counter

has been reset, you can read the new

value on the display when the machine

is switched on again.

The electronic board has a function testing

feature as an aid to troubleshooting in the

event of a machine failure.

Execute steps 1, 2 and 3 described in the

previous section. If any component fails to

work during the test, proceed as follows:

-Verify that the component is connected

correctly and is energised. If this is OK

and the component still fails, replace it by

a new one.

-If the component is not energised, check

the voltage at the output of the electronic

board when the associated LED is on. If

there is no voltage, change the electronic

board.

8

ENGLISH

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Sammic V-410 T Máquina vácuo. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Sammic. Eles podem fornecer um manual original. Você está procurando o manual do seu Sammic V-410 T Máquina vácuo em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Sammic Máquinas vácuo
Mais manuais de Máquinas vácuo

Produtos relacionados

Manual

Sammic V-821 T Máquina vácuo

Manual

Sammic V-204 T Máquina vácuo

Manual

Sammic V-253 T Máquina vácuo

Manual

Sammic V-421 T Máquina vácuo

Manual

Sammic V-426 T Máquina vácuo

Manual

Sammic V-641 T Máquina vácuo

Manual

Neff N17XH10G0 Máquina vácuo

Manual

Adler AD 4509 Máquina vácuo

Categorias relacionadas