Manual AEG BHC92420XA Exaustor

Manual

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 13:

Button A: light switch. Button B: first speed motor ON/OFF switch.

Button C: second speed switch. Button D: third speed switch.

Controls shown in Fig. 14:

Button A: Light switch; position 0: light off; position 1: light on. Button B: Motor

switch; position 0: motor off; position 1-2-3: motor on at speed I, II and III.

Controls shown in Fig. 15:

Key A = Light ON/OFF switch.

Key B = Motor ON/OFF switch - Speed I

Key C = Motor ON/OFF switch - Speed II

Key D = Motor ON/OFF switch - Speed III

Key E = Motor ON/OFF switch - Speed IV (intensive).

Filter alarm:

After 30 hours of operation, with the motor off, the speed keys (keys B, C, D and E) are on for 30 seconds to indicate

the grease filters need cleaning. After cleaning the grease filters, restart the hour counter (RESET) by pressing one of

the keys (B, C, D and E) during filter alarm.

After 120 hours of operation, with the motor off, the speed keys (keys B, C, D and E) flash for 30 seconds to indicate

the grease filters need cleaning and the charcoal filters replaced. Restart the hour counter (RESET) by pressing one of

the keys (B, C, D and E) during filter alarm.

Timer 5'; the timer can be started (switch-off delayed by 5 minutes) by pressing the keys B, C, or D for 2 seconds when

the motor is running; the selected speed key starts flashing.

Controls shown in Fig. 16:

Key A : Motor ON/OFF switch - Speed I

Key B : MOTOR / RESET FILTER ALARM. Increases and decreases the motor speed. When pressing the key (about

2 seconds) during display of the filter alarm (motor off) its reset the hour counter.

Key C : TIMER. When pressing the key when the motor is running, the TIMER is activated and the hood will automatically

be switched off after 5 minutes.

Key D : switches the lights on/off.

FILTER ALARM: After 30h of operation, all the LEDs are on. It indicates that the grease filters need to be cleaned.

After 120h of operation, all the LEDs are blinking; It indicates that the grease filters need to be cleaned and the charcoal

filters replaced.

After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing the

key B during display of the filter alarm.

Pay special attention to the grease filters; to remove the filter: push inward on the clamp at the handle andpull the filter

downward. Wash out the filter using a neutral soap.

If the model purchased has the controls shown in Figure 13/14:

the grease filter must be cleaned periodically: exactly how often depends on use (at leastonce every other month). If

the model purchased has the controls shown in Figure 15 and 16: see the Controls in Fig.15 / 16 (Filter alarm) in the

paragraph entitled “Operation”.

Charcoal filter/s: if using the hood in the filtering hood, the charcoal filter must be replaced periodically. To

remove the charcoal filters, proceed as follows, depending on the model purchased:

- if the hood features round charcoal filters (Fig. 17), remove the charcoal filter by turning counter-clockwise.

- if the hood features a panel type charcoal filter (Fig. 12), remove the charcoal filter by first of all removing

the two filter retainers M.

If the model purchased has the controls shown in Figure 13/14, the charcoal filters must be replaced according

to use: on the average once every 6 months. If the model purchased has the controls shown in Figure 15 and

16, see the Controls in Fig.15 / 16 (Filter alarm) in the paragraph entitled “Operation”.

Lighting:

- To replace the

incandescence bulbs, remove the fixture: apply a slight pressure on the 2 stops and at the

sametime push the fixture downwards (Fig.18).

- To change the halogen lamps shown in Fig. 19 open the cover levering from the proper slots. CAUTION: Do

not handle glass bulb with bare hands.

Replace it with lamps of the same type; if a lamp is not listed in the table shown in the “Warning” worksheet,

please contact the support center.

The motor used in this hood features a safety device (thermal cutout) that responds to temperature

changes For accidental reasons or due to installation faults, this device could engage and automatically

shut off the motor, thereby preventing serious damage to the equipment. In such cases, after allowing

the motor to cool down, the hood can be switched on again; the cause of the fault will nonetheless

have to be remedied, ensuring installation has been correctly made and that all the instructions in the

Information sheet have been complied with.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu AEG BHC92420XA Exaustor. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com AEG. Eles podem fornecer um manual original. Você está procurando o manual do seu AEG BHC92420XA Exaustor em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para AEG Exaustores
Mais manuais de Exaustores

Perguntas frequentes sobre AEG BHC92420XA Exaustor

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

AEG IDE84241IB Exaustor

Manual

AEG DK9190-M Exaustor

Manual

AEG DPE5660G Exaustor

Manual

AEG 8060D-M Exaustor

Manual

AEG DGK6681HM Exaustor

Manual

AEG DGE5861HR Exaustor

Manual

AEG DD9663-M Exaustor

Manual

AEG DGB3523S Exaustor

Categorias relacionadas