Manual Steinel RS LED D2 Candeeiro

Manual

- 9 -

- 8 -

T

he SensorLight can be put into operation as soon as

t

he enclosure  has been fitted and the SensorLight

has been connected to the mains power supply.

Putting the light into operation manually at the light

switch turns it OFF after 10 secs. for the calibration

phase. Once calibrated, it is activated for the sensor

m

ode. It is not necessary to operate the light switch a

s

econd time.

Reach setting (sensitivity) 

Factory setting: 8 m.

Reach can be infinitely varied from

3 m to 8 m.

Turned fully anticlockwise =

min. reach (3 m)

Turned fully clockwise =

max. reach (8 m)

Reach is the term used to describe the diameter of

the more or less circular detection zone produced on

the ground after mounting the SensorLight at a height

of 2.5 m.

Time setting (switch-off delay) 

Factory setting: 5 sec.

Light ON duration can be infinitely

varied from 5 sec. to 15 min.

Turned fully anticlockwise =

shortest ON time (5 sec.)

Turned fully clockwise =

= longest ON time (15 min.)

Any movement detected before this time elapses will

re-start the timer. The shortest time setting is recom-

mended when adjusting the detection zone and per-

forming a functional test.

Note: After the light switches

'OFF', it takes approx.

1 sec. before it is able to start detecting movement

again. The light will only switch

'ON' in response to

movement once this period has elapsed.

Twilight setting (response threshold) 

Factory setting: 2000 lux

The response threshold can be

infinitely varied from 2 – 2000 lux.

Adjustment control set to:

= Night-time operation (2 lux)

= daylight operation (2000 lux)

When adjusting the detection zone and performing

the walk test in daylight, the control must be set

to .

Functions

- 9 -

Functional Warranty

This STEINEL product has been manufactured with

great care, tested for proper operation and safety in

accordance with applicable regulations and then sub-

jected to random sample inspection. STEINEL guar-

antees that it is perfect condition and proper working

order. The warranty period is 36 months, starting on

the date of sale to the consumer. We will remedy

defects caused by material flaws or manufacturing

faults. The warranty will be met by repair or replace-

ment at our own discretion. The warranty shall not

cover damage to wear parts, damage or defects

caused by improper treatment or maintenance.

Further consequential damage to other objects is

excluded.

Claims under the warranty will only be accepted if the

unit is sent fully assembled and well packed complete

with a brief description of the fault, a receipt or

invoice (date of purchase and dealer's stamp) to the

appropriate Service Centre.

Repair Service:

Please ask your nearest service centre

how to proceed for repairing faults not

covered by the warranty or occurring

after the warranty expires.

Declaration of conformity

This product complies with

- Low Voltage Directive 2006/95/EC

- EMC Directive 2004/108/EC

-

RoHS Directive 2011/65/EC

-

R&TTE Directive 1999/05/EC

Installation

Important: Make sure the installation site is

not sub-

ject to

vibration.

C

onnecting a dimmer will result in damage to the

S

ensorLight.

1

. Hold enclosure  against the wall/ceiling and

mark drill holes, paying attention to any existing

wiring in the wall/ceiling.

2. Drill the holes, insert wall plugs (6 mm dia.).

3. Pierce sealing plug for power supply lead.

4. Pass power supply leads through.

5. Screw enclosure  into place.

6. Connecting the mains power supply lead (see fig.).

The mains power supply lead is a 3-core cable:

L = phase conductor (usually black or brown)

N = neutral conductor (usually blue)

PE = protective earth conductor (green/yellow)

If you are in any doubt, identify the conductors using

a voltage tester; switch

'OFF' the current again.

Connect the phase conductor (L) and neutral con-

ductor (N) to the terminal block. Insulate any PE

protective earth conductor with adhesive tape.

Technical specifications

Dimensions (HxWxD): 300 x 300 x 65.5 mm

Material: plastic

Mains voltage: 220 – 240 V, 50/60 Hz

Output: 11 W LED / 600 lm / 55 lm/W

Colour temperature: 3000 kelvin (warm white)

LED life expectancy: 50.000 hours

HF-system: 5.8 GHz

Angle of coverage: 360° with 160° aperture angle also through glass, wood and stud walls

Detection reach: 3 m – 8 m all round

Twilight setting: 2 – 2000 lux

Time setting: 5 sec. to 15 min.

IP rating: IP 20

Protection class: II

Power consumption: approx. 0.4 W

Temperature range: -10° C to +40 °C

- 8 -

7. Set functions , , .

8

. Fit shade.

S

urface wiring:

Surface wiring can be carried out as shown in

diagram I on page 2.

GB

Ø 3 m – 8 m dia.

5 sec. - 15 min.

2 – 2000 lux

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Steinel RS LED D2 Candeeiro. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Steinel. Eles podem fornecer um manual original. Você está procurando o manual do seu Steinel RS LED D2 Candeeiro em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Steinel Candeeiros
Mais manuais de Candeeiros

Perguntas frequentes sobre Steinel RS LED D2 Candeeiro

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Steinel RS PRO LED P2 S FLAT Candeeiro

Manual

Steinel RS 100 L Candeeiro

Manual

Steinel RS LED D1 Candeeiro

Manual

Steinel RS 16 LED Candeeiro

Manual

Steinel RS LED M2 Candeeiro

Manual

Steinel RS PRO LED P2 S Candeeiro

Manual

Steinel RS LED M1 Candeeiro

Manual

Steinel RS PRO LED P3 S Candeeiro

Categorias relacionadas