Manual Philips GC2510 Ferro

Manual

ENGLISH

General description (Fig. 1)

A Spray nozzle

B Capofllingopening

C Steam control

O = no steam

l =minimumsteam

; =maximumsteam

1=Calc-Cleanfunction

D Shot-of-steambutton9

E SpraybuttonT

F Automaticshut-offlight(GC2560only)

G Mainscord

H Anti-Calctablet(alltypesexceptGC2522en

GC2510)

I Temperaturelight

J Type plate

K Water tank

L Temperaturedial

Important

Readtheseinstructionsforusecarefullybeforeusingthe

applianceandsavethemforfuturereference.

Check if the voltage indicated on the type plate

corresponds to the local mains voltage before you

connect the appliance.

Only connect the appliance to an earthed wall

socket.

Do not use the appliance if the plug, the cord or

the appliance itself shows visible damage, or if the

appliance has been dropped or is leaking.

Check the cord regularly for possible damage.

If the mains cord is damaged, it must be replaced

by Philips, a service centre authorised by Philips

or similarly qualied persons in order to avoid a

hazard.

Never leave the appliance unattended when it is

connected to the mains.

Never immerse the iron and the stand, if provided,

in water.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

The soleplate of the iron can become extremely

hot and may cause burns if touched.

Do not allow the cord to come into contact with

the soleplate when it is hot.

When you have nished ironing, when you clean

the appliance, when you ll or empty the water

tank and also when you leave the iron even for a

short while: set the steam control to position O,

put the iron on its heel and remove the mains plug

from the wall socket.

Always place and use the iron and the stand, if

provided, on a stable, level and horizontal surface.

This appliance is intended for household use only.

Electromagnetic elds (EMF)

ThisPhilipsappliancecomplieswithallstandards

regardingelectromagneticelds(EMF).Ifhandled

properlyandinaccordancewiththeinstructionsinthis

instructionmanual,theapplianceissafetouseaccording

toscienticevidenceavailabletoday.

Preparing for use

Filling the water tank

1 Remove the mains plug from the wall socket.

2 Set the steam control to position O (= no

steam) (Fig. 2).

3 Open the cap of the lling opening.

4 Tilt the iron and ll the water tank up to maximum

level (Fig. 3).

If the tap water in your area is very hard, we advise you

to use distilled water.

Do not use chemically descaled water.

Do not ll the water tank beyond the MAX indication.

Do not put perfume, vinegar, starch, descaling agents,

ironing aids or other chemicals in the water tank.

-

-

-

-

,

,

,

,

,

,

,

,

,

,

,

,

,

,

5 Close the cap of the lling opening (‘click’).

Setting the temperature

The iron may give off some smoke when you use it

for the rst time. This will cease after a short while.

1 Put the iron on its heel and set the temperature

dial to the required ironing temperature by turning

it to the appropriate position (Fig. 4).

Checkthelaundrycarelabelfortherequiredironing

temperature.

1 Syntheticfabrics(e.g.acrylic,viscose,

polyamide,polyester)

1 Silk

2 Wool

3Cotton,linen

Ifyoudonotknowwhatkindorkindsoffabric

anarticleismadeof,determinetherightironing

temperaturebyironingapartthatwillnotbevisible

whenyouwearorusethearticle.

Silk,woollenandsyntheticmaterials:ironthereverse

sideofthefabrictopreventshinypatches.Avoid

usingthesprayfunctiontopreventstains.

2 Put the mains plug in an earthed wall socket.

3 When the temperature light has gone out, wait a

while before you start ironing.

Note: The temperature light will go on from time to time

during ironing.

Using the appliance

Steam ironing

Makesurethatthereisenoughwaterinthewatertank.

1 Set the temperature dial to the recommended

position (see section ‘Setting the temperature’).

2 Set the steam control to the appropriate steam

position (Fig. 2).

çforminimumsteam(temperaturesettings2and

3).

éformaximumsteam(temperaturesettings3

toMAX).

Note: The iron will start steaming as soon as the set

temperature has been reached.

GC2640/GC2620/GC2530/GC2528/GC2520/

GC2510 only:

Watermayleakfromthesoleplateifthesettemperature

istoolow(MINto

2).

Ironing without steam

1 Set the steam control to position O (= no steam).

2 Set the temperature dial to the recommended

position (see section ‘Setting the temperature’).

Features

Spray function

Youcanusethesprayfunctiontoremovestubborn

creasesatanytemperature

1 Make sure that there is enough water in the water

tank.

2 Press the spray button several times to moisten the

article to be ironed (Fig. 5).

Shot of steam

Apowerfulshotofsteamhelpstoremoveverystubborn

creases.

Theshot-of-steamfunctiononlyworksattemperature

settingsbetween

2andMAX.

1 Press and release the shot-of-steam button (Fig. 6).

Vertical shot of steam (all types except

GC2510)

1 The shot-of-steam function can also be used when

you are holding the iron in vertical position. This is

useful for removing creases from hanging clothes,

curtains, etc (Fig. 7).

Never direct the steam at people.

Drip stop (GC2652/GC2650/GC2560/

GC2522 only)

Thisironisequippedwithadripstopfunction:the

ironautomaticallystopsproducingsteamwhenthe

,

-

-

-

-

-

-

-

-

-

temperatureistoolowtopreventwaterfromdripping

outofthesoleplate.Whenthishappensyouwillheara

click.

Automatic shut-off (GC2560 only)

Theelectronicshut-offfunctionautomaticallyswitches

theheatingelementoffiftheironhasnotbeenmoved

forawhile.

The automatic shut-off light starts blinking to

indicate that the heating element has been switched

off (Fig. 8).

Tolettheironheatupagain,picktheironupormoveit

slightly.Theautomaticshut-offlightgoesout.

1 If the temperature light goes on, wait for it to go

out before you start ironing.

2 If the temperature light does not go on, the iron is

ready for use.

Cleaning and maintenance

Double-Active Calc System

All types except GC2510: The Anti-Calc tablet

prevents scale from clogging the steam vents. The

tablet is constantly active and does not need to be

replaced (Fig. 9).

The Calc-Clean function removes the scale

particles.

Calc-Clean function

UsetheCalc-Cleanfunctiononceeverytwoweeks.Ifthe

waterinyourareaisveryhard(i.e.whenakescomeout

ofthesoleplateduringironing),theCalc-Cleanfunction

shouldbeusedmorefrequently.

1 Set the steam control to position O.

2 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the

water tank..

3 Set the temperature dial to MAX (Fig. 10).

4 Put the plug in the wall socket.

5 Unplug the iron when the temperature light has

gone out.

6 Hold the iron over the sink and set the steam

control to the Calc-Clean position (1). The steam

control will spring up slightly.

7 Pull the steam control upwards and remove

it (Fig. 11).

8 Hold the iron over the sink and move it to and

fro (Fig. 12).

Note: Steam and boiling water will come out of the soleplate.

Impurities and scale (if any) will be ushed out.

9 Use vinegar to remove scale, if any, from the steam

control needle (Fig. 13).

Do not bend or damage the steam control needle.

10 Put the steam control back into the iron by

inserting the point of the needle exactly in

the centre of the hole and by tting the small

projection on the side of the needle into the slot.

Press down the steam control while turning it to

position O (Fig. 14).

11 Repeat the Calc-Clean process if the iron still

contains a lot of impurities.

After the Calc-Clean process

1 Put the plug in the wall socket and let the iron heat

up to allow the soleplate to dry.

2 Unplug the iron when the temperature light has

gone out.

3 Move the iron gently over a piece of used cloth to

remove any water stains that may have formed on

the soleplate.

Storage

1 Set the steam control to position O, remove the

plug from the wall socket and let the iron cool

down.

2 Clean the appliance and wipe scale and any other

deposits off the soleplate with a damp cloth and a

non-abrasive (liquid) cleaner.

,

,

,

4239.000.6140.3

2/9

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Philips GC2510 Ferro. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Philips. Eles podem fornecer um manual original. Você está procurando o manual do seu Philips GC2510 Ferro em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Philips Ferros
Mais manuais de Ferros

Perguntas frequentes sobre Philips GC2510 Ferro

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Philips GC9520 PerfectCare Ferro

Manual

Philips GC9666 PerfectCare Elite Plus Ferro

Manual

Philips PSG2000 Ferro

Manual

Philips HI124 Ferro

Manual

Philips GC9420 Ferro

Manual

Philips DST7511 Azur Ferro

Manual

Philips HI126 Ferro

Manual

Philips DST7031 Ferro

Categorias relacionadas