Manual Makita UR360D Aparador de relva

Manual

9

Installing or removing battery cartridge

(Fig. 5)

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool while

sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being inserted

correctly.

Power switch action

WARNING:

• Before inserting the battery cartridge in the tool,

always check to see that the switch trigger

actuates properly and returns to the “OFF”

position when released. Do not pull the switch

trigger hard without pressing in the lock-off button.

This can cause switch breakage. Operating a tool

with a switch that does not actuate properly can lead to

loss of control and serious personal injury. (Fig. 6)

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, press in the lock-off button and pull the

switch trigger. The tool speed is increased by increasing

pressure on the switch trigger. Release the switch trigger

to stop.

Reversing Switch for Debris Removal

(Fig. 7)

This tool has a reversing switch. Reversing is used only

when weeds and debris are entangled in the tool. To

operate the tool normally the “A” side of the switch should

be depressed.

If weeds and debris are jammed in the rotating head, the

tool can be reversed by depressing the “B” side of the

switch. In the reverse position, the tool only operates for a

short period of time and automatically shut off.

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before removing

weeds or debris entangled in the tool that is not

removed by the reverse mode. Failure to switch off

and remove the battery cartridge may result in serious

personal injury from accidental start-up.

NOTICE:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Do not change the direction of rotation

while the head is still rotating, the tool may be

damaged.

Speed change (Fig. 8)

Two speed ranges can be preselected with the speed

change switch.

Flipping the speed change switch lever to the “1” position

will set the tool to the low speed range and the “2” position

will set the tool to the high speed range.

Battery/motor protection system

The battery cartridge and tool are provided with protection

functions that will automatically reduce or cut off power

when overload situations occur that may cause damage

to the tool or battery cartridge.

If the tool becomes overloaded but not locked up, a

protector is provided to reduce the revolutions to protect

the motor. In this case the two indicator lamps described

in the table below do not light or blink.

All other protection functions can be identified by the

indicator lights described in the table below. (Fig. 9)

010823

Status Action to be taken

– Blinking Battery power has been nearly used up.

Replace the battery with fully charged

one.

– Lighting On

Battery protector is shutting off the power

- battery power has been used up.

Replace the battery with fully charged

one.

Blinking –

Overload protector is shutting off the

power - the motor was locked.

Release the switch trigger and remove

the cause of the motor lock or overload.

If the cutting tool is locked by entangling

weeds or the like, always remove the

battery cartridge before clearing it.

Lighting On –

Overheat protector is shutting off the

power - overheating.

Rest the equipment for a while.

Blinking Blinking Electric or electronic malfunction

Ask your local authorized service center

for repairs.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita UR360D Aparador de relva. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita UR360D Aparador de relva em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Aparadores de relva
Mais manuais de Aparadores de relva

Produtos relacionados

Manual

Makita DUR190L Aparador de relva

Manual

Makita BUR141 Aparador de relva

Manual

Makita DUR191L Aparador de relva

Manual

Makita DUR141 Aparador de relva

Manual

Makita DBC260U Aparador de relva

Manual

Makita DUR366LZ Aparador de relva

Manual

Makita BUR181 Aparador de relva

Manual

Makita DUR364L Aparador de relva

Categorias relacionadas