Manual Makita DUR362L Aparador de relva

Manual

16

weeds or debris entangled in the tool that could not

be removed when operated in the reverse mode.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

For model DUR361U (Fig. 12)

For model DUR362L (Fig. 13)

This tool has a reversing switch which is only provided to

change the direction of rotation so that it can be used to

remove weeds and debris entangled in the tool. To

operate the tool normally the “A” side of the switch should

be depressed.

To remove weeds and debris that are jammed in the

rotating head the tool can be reversed by depressing the

“B” side of the switch. In the reverse position the tool will

only operate for a short period of time and automatically

shut off.

NOTICE:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage it.

Speed adjusting dial (Fig. 14)

The tool speed can be adjusted by turning the adjusting

dial. Turn the speed adjusting dial clockwise for higher

speed, and counterclockwise for lower speed.

Nylon cutting head (optional accessory

for a product that comes with a cutter

blade)

Nylon cutting head

NOTICE:

• Do not attempt to bump feed the head while the tool is

operating at a high RPM. Bump feeding at a high RPM

may cause damage to the nylon cutting head.

• The bump feed will not operate properly if the head is

not rotating. (Fig. 15)

The nylon cutting head is a dual string trimmer head

provided with a bump & feed mechanism.

To cause the nylon cord to feed out, the cutting head

should be bumped against the ground while rotating at a

low RPM.

NOTE:

If the nylon cord does not feed out while bumping the

head, rewind/replace the nylon cord by following the

procedures described under “Maintenance.”

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out

any work on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembled state may result in serious personal injury

from accidental start-up.

Installing the handle

For model DUR361U (Fig. 16)

Insert the shaft of the handle into the grip as shown. Align

the screw hole in the grip with the one in the shaft. Tighten

the screw securely.

Fit the barrier and grip onto the shaft pipe with four

screws. Make sure that the spacer on the shaft pipe is

located between the grip/barrier assembly and the

hanger.

Place handle between handle clamp and handle holder.

Adjust the handle to an angle that provides a comfortable

working position and then secure by firmly hand-

tightening knob. (Fig. 17)

For model DUR362L (Fig. 18)

Fit the grip onto the shaft pipe and tighten it with two hex

bolts. Make sure that the spacer on the shaft pipe is

located between the grip assembly and the other grip. Do

not remove or shrink the spacer.

Installing the guard

WARNING:

• Never use the tool without the guard illustrated in

place. Failure to do so can cause serious personal

injury.

For cutter blade (only for model DUR361U) (Fig. 19)

Install the protrusion of the protector clamp to the gear

case until aligning the position with the label on the pipe.

Fix the protector to the protector clamp with the two bolts

and then tighten both bolts by the hex wrench evenly.

(Fig. 20)

For nylon cutting head

For DUR362L (Fig. 21)

Align the protrusions on the protector attachment with the

grooves of the protector.

Align the protrusions on the protector holder attachment

with the groove of the protector holder. (Fig. 22)

After attaching the protector and the protector holder,

tighten the hex bolts securely. (Fig. 23)

For DUR361U (optional accessory)

Remove the hex bolts with hex wrench. Then remove the

protector clamp and protector. (Fig. 24)

Install the protector attachment and protector holder

attachment to the gear case.

To install the protector for nylon cutting head, follow the

installing method mentioned previously. (Fig. 25)

Installing the wire guard

CAUTION:

• Before adjusting the wire guard, wait for the cutting

head comes to standstill. Do not adjust the wire guard

with your foot.

To reduce the risk damaging the objects in front of the

cutting head, insert the wire guard so that it controls the

cutting range of the mowing line. (Fig. 26)

Slightly expand the wire guard outward and then insert it

into the holes of the protector. (Fig. 27)

NOTE:

• Do not expand the wire guard outward too much.

Otherwise it may break.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita DUR362L Aparador de relva. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita DUR362L Aparador de relva em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Aparadores de relva
Mais manuais de Aparadores de relva

Produtos relacionados

Manual

Makita UR3000 Aparador de relva

Manual

Makita BBC231UD Aparador de relva

Manual

Makita EBH341U Aparador de relva

Manual

Makita BBC300L Aparador de relva

Manual

Makita DUR189 Aparador de relva

Manual

Makita BBC300LD Aparador de relva

Manual

Makita DUR192L Aparador de relva

Manual

Makita DUR190L Aparador de relva

Categorias relacionadas