Manual Makita DUR362L Aparador de relva

Manual

14

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it is

severely damaged or is completely worn out. The

battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. Follow your local regulations relating to disposal

of battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the battery

cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room

temperature at 10°C - 40°C (50°F - 104°F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use it for

a long period (more than six months).

Parts description (Fig. 4)

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool. Failure to switch off

and remove the battery cartridge may result in serious

personal injury from accidental start-up.

Installing or removing battery cartridge

(Fig. 5)

CAUTION:

• Always switch off the tool before installing or removing

of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool while

sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip it

into place. Insert it all the way until it locks in place with a

little click. If you can see the red indicator on the upper

side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being inserted

correctly.

NOTE:

• The tool does not work with only one battery cartridge.

Tool/battery protection system

The tool is equipped with a tool/battery protection system.

This system automatically cuts off power to the motor to

extend tool and battery life.

The tool will automatically stop during operation if the tool

or battery are placed under one of the following

conditions. In some conditions, the indicators light up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops and battery indicators blink. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool (Fig. 6)

When the tool is overheated, the tool stops automatically

and the power indicator blinks about 60 seconds. In this

situation, let the tool cool before turning the tool on again.

Overheat protection for battery

When the battery is overheated, the tool stops

automatically and the battery indicators light up. The tool

does not start even if pulling the switch trigger. In this

situation, let the battery cool before turning the tool on

again.

NOTE:

The battery overheat protection works only with a battery

cartridge with a star marking. (Fig. 7)

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the product does not operate even when

the switches are operated, remove the batteries from the

tool and charge the batteries.

Indicating the remaining battery capacity

(Only for battery cartridges with “B” at the end of the

model number.) (Fig. 8)

Press the check button on the battery cartridge to indicate

the remaining battery capacity. The indicator lamps light

up for few seconds.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita DUR362L Aparador de relva. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita DUR362L Aparador de relva em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Aparadores de relva
Mais manuais de Aparadores de relva

Produtos relacionados

Manual

Makita UR3000 Aparador de relva

Manual

Makita BBC231UD Aparador de relva

Manual

Makita EBH341U Aparador de relva

Manual

Makita BBC300L Aparador de relva

Manual

Makita DUR189 Aparador de relva

Manual

Makita BBC300LD Aparador de relva

Manual

Makita DUR192L Aparador de relva

Manual

Makita DUR190L Aparador de relva

Categorias relacionadas