Manual Makita DUR141 Aparador de relva

Manual

11

Power switch action

WARNING:

• Before inserting the battery cartridge in the tool,

always check to see that the switch trigger

actuates properly and returns to the “OFF”

position when released. Do not pull the switch

trigger hard without pressing in the lock-off button.

This can cause switch breakage. Operating a tool

with a switch that does not actuate properly can lead to

loss of control and serious personal injury.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, move the lock-off button forward and pull

the switch trigger. Release the switch trigger to stop.

(Fig. 8)

Indication lamp (Fig. 9)

Running the tool allows the indication lamp to show the

battery cartridge capacity status.

When the tool is also overloaded and has stopped during

operation, the lamp lights up in red.

Refer to the following table for the status and action to be

taken for the indication lamp.

Note 1: The time at which the indication lamp lights up varies by the temperature around the work area and the battery

cartridge conditions.

012443

Adjusting the shaft length

WARNING:

• Before adjusting the shaft length, release the switch

trigger and remove the battery cartridge from the string

trimmer. Failure to release the trigger and removing the

battery cartridge may cause a personal injury.

To adjust the length of the shaft, turn the grip

counterclockwise until the shaft is unlocked and pull out or

push in to the desired length. (Fig. 10)

Nylon cutting head

NOTICE:

• The bump feed will not operate properly if the nylon

cutting head is not rotating.

The nylon cutting head is a single string trimmer head

provided with a bump & feed mechanism.

To cause the nylon cord to feed out, the cutting head

should be bumped against the ground while the tool is

running. As the nylon cord is feeding out it will

automatically be cut to the proper length by the cutter on

the guard. (Fig. 11)

NOTE:

• If the nylon cord does not feed out while bumping the

head, rewind/replace the nylon cord by following the

procedures described under “Installing or removing the

nylon cutting head” and “Winding a new nylon cord on

the spool.”

• Do not bump the tool to the concrete or asphalt

surface. Bumping to this kind of objects may cause the

tool damage.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out

any work on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembled state may result in serious personal injury

from accidental start-up.

Installing the front grip (Fig. 12)

Put the front grip on the front grip holder and secure it with

a hex bolt and the clamping nut provided with the string

trimmer as shown in the figure. At this time, the hex bolt

needs to be installed from the side in which the hex bolt

lock port is located and the clamping nut needs to be

installed from the opposite side.

NOTE:

• The front grip has a edge-to-edge cut slit in its

mounting area. Using this slit allows you to easily install

the front grip on the front grip holder.

The front grip angle is adjustable. To adjust the front grip

angle, loosen the claming nut, set the front grip at an

proper angle according to your work and then tighten the

nut clockwise firmly.

Installing the guard

CAUTION:

• While installing the guard, be careful not to contact

the nylon cord cutter provided on the guard.

Contact with the cutter could result in personal injury.

Mount the guard by fitting it on to the motor housing so

that the nylon cord is not pinched between the guard and

Indication lamp Status Action to be taken

The lamp blinks in red. This indicates the appropriate time to

replace the battery cartridge when the

battery power becomes low.

Recharge the battery cartridge as soon

as possible.

The lamp lights up in red.

(Note 1)

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Recharge the battery cartridge.

The lamp lights up in red.

(Note 1)

Autostop due to overload. Turn off the tool.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita DUR141 Aparador de relva. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita DUR141 Aparador de relva em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Aparadores de relva
Mais manuais de Aparadores de relva

Produtos relacionados

Manual

Makita DUR193 Aparador de relva

Manual

Makita DUR189 Aparador de relva

Manual

Makita DBC260L Aparador de relva

Manual

Makita DUR369LPT2 Aparador de relva

Manual

Makita DUR369AZ Aparador de relva

Manual

Makita DUR369A Aparador de relva

Manual

Makita BUR181 Aparador de relva

Manual

Makita DUR368AZ Aparador de relva

Categorias relacionadas