Manual Makita DBC260U Aparador de relva

Manual

15

ADJUSTMENT OF LOW-SPEED REVOLUTIONS (IDLING)

The cutter blade or the nylon cutting head should not rotate when the control

lever is fully released. If necessary, adjust the idling rpm using the idling

adjustment screw.

Checking the Idling speed

– The idling speed should be set to 3,000 min

-1

.

If necessary, adjust the idling speed using the idling screw (the blade or the

nylon cutting head must not turn when the engine is idling).

Tightening the idling screw (1) increases the engine revolutions, whereas

loosening the idling screw reduces the engine revolutions.

CAUTION: The cutting tools listed below must only be resharpened by an

authorized facility. Manual resharpening will result in imbalances of

the cutting tool, which will cause vibrations and damage to the

equipment.

– cutter blade (star blade (4 teeth), eddy blade (8 teeth))

A professional resharpening and balancing service is provided by Authorized

Service Agents.

NOTE: To increase the service life of the cutter blade (star blade, eddy blade)

the blade may be turned over to allow both cutting edges to wear.

NYLON CUTTING HEAD

The nylon cutting head is a dual string trimmer head capable of both automatic

and bump & feed mechanisms.

The nylon cutting head will automatically feed out the proper length of nylon cord

by the changes in centrifugal force caused by increasing or decreasing rpms.

However, to cut soft grass more efficiently, bump the nylon cutting head against

the ground to feed out extra cord as shown in operation section.

Operation

– Increase the nylon cutting head speed to approx. 6,000 min

-1

.

Nylon cord will not feed out correctly at lower speeds (under 4,800 min

-1

).

– The most effective cutting area is shown by the shaded area in the diagram to

the right.

If the nylon cord does not feed out automatically, follow the instructions below:

1. Release the throttle lever so that the engine idles, and then squeeze the

throttle lever fully. Repeat this procedure until the nylon cord feeds out to the

proper length.

2. If the nylon cord is too short to feed out automatically using the procedure

above, bump the knob of the nylon cutting head against the ground to feed

out the nylon cord.

3. If the nylon cord does not feed out using procedure 2, rewind/replace the

nylon cord by following the procedures described under “Replacing the nylon

cord”.

Replacing the nylon cord

– Stop the engine.

– Press the housing latches inward to lift off the cover, then remove the spool.

Resharpening the cutting tool

(1)

Slow High

Most effective cutting area

Knob

Idle speed Full speed

Cover

Latches

Press

Press

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita DBC260U Aparador de relva. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita DBC260U Aparador de relva em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Aparadores de relva
Mais manuais de Aparadores de relva

Produtos relacionados

Manual

Makita DUR369A Aparador de relva

Manual

Makita BUR181 Aparador de relva

Manual

Makita DUR192L Aparador de relva

Manual

Makita UR3000 Aparador de relva

Manual

Makita DUR368A Aparador de relva

Manual

Makita UR101C Aparador de relva

Manual

Makita DUR190L Aparador de relva

Manual

Makita EBH341U Aparador de relva

Categorias relacionadas