Manual Makita BTD062 Chave de impacto

Manual

5

4. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

5. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

6. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

7. Be careful not to drop, shake or strike battery.

8. Do not charge inside a box or container of any

kind. The battery must be placed in a well venti-

lated area during charging.

ADDITIONAL SAFETY RULES FOR TOOL

ENB024-1

1. Be aware that this tool is always in an operating

condition, because it does not have to be

plugged into an electrical outlet.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a “live”

wire will make exposed metal parts of the tool

“live” and shock the operator.

3. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

4. Hold the tool firmly.

5. Wear ear protectors.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig.1)

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Charging (Fig. 2)

1. Plug the battery charger into your power source. Two charging lights will flash in green color repeatedly.

2. Insert the battery cartridge into charger until it stops adjusting to the guide of charger. Terminal cover of charger

can be opened with inserting and closed with pulling out the battery cartridge.

3. When the battery cartridge is inserted, the charging light color will change from green to red and charging will

begin. The charging light will keep lighting up lit steadily during charging. One red charging light indicates charged

condition in 0 – 80% and two red ones indicates 80 – 100%.

4. With finish of charge, the charging lights will change from two red ones to two green ones.

5. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its

“trickle charge (maintenance charge)” mode which will last approximately 24 hours.

6. After charging, unplug the charger from the power source.

NOTE:

• The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufac-

turer’s batteries.

• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it

may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-

tery cartridge fully after discharging it completely and recharging a couple of times.

• If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location

exposed to direct sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a while.

Charging will begin after the battery cartridge is cooled by the cooling fan installed in the charger. When the temper-

ature on battery is more than approx. 70°C, two charging lights may flash in red color, and when approx. 50°C –

70°C, one charging light in red color.

• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger

or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.

Battery Type Capacity (mAh) Number of cells Charging time

BH9020A 2,000 8 Approx. 30 min.

BH9033A 3,300 8 Approx. 50 min.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Makita BTD062 Chave de impacto. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Makita. Eles podem fornecer um manual original. Você está procurando o manual do seu Makita BTD062 Chave de impacto em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Makita Chaves de impacto
Mais manuais de Chaves de impacto

Perguntas frequentes sobre Makita BTD062 Chave de impacto

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Makita 6916D Chave de impacto

Manual

Makita BTD147 Chave de impacto

Manual

Makita BTW250 Chave de impacto

Manual

Makita DTD136 Chave de impacto

Manual

Makita DTL060 Chave de impacto

Manual

Makita 6914D Chave de impacto

Manual

Makita 6960D Chave de impacto

Manual

Makita TD0101 Chave de impacto

Categorias relacionadas