8 1
76
2
3 4 5
1.
2.
x4
3.
DTN42-0970
1101048514-DOM
5+
service.mattel.com
APPLY LABELS
ASSEMBLY
TO PLAY
CONTENTS
©2016 Mattel. All Rights Reserved. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services
1-800-524-8697. Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628 500303. Mattel Australia
Pty., Ltd., Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. Mattel East Asia Ltd., Room 503-09, North
Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: (852) 3185-6500. Diimport & Diedarkan Oleh: Mattel
Southeast Asia Pte. Ltd. , No 19-1, Tower 3 Avenue 7, Bangsar South City, No 8, Jalan Kerinchi, 59200 Kuala Lumpur,
Malaysia. Tel: 03-78803817, Fax: 03-78803867.
BATTERY SAFETY INFORMATION
In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
Protect the environment by not disposing of this product with household waste [2012/19/EU].
Check your local authority for recycling advice and facilities.
CONNECT TO OTHER HOT WHEELS
®
SETS (SOLD SEPARATELY).
BATTERY INSTALLATION
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 4 "D" size (LR20) alkaline batteries (not included) in the orientation (+/-) shown.
• Replace battery cover and tighten screws.
• For longer life use alkaline batteries.
• Replace batteries when booster can no longer propel car through the track set.
• When exposed to an electrostatic source, the product may malfunction. To resume normal operation,
switch the power OFF for a few seconds, and then ON again.
MORE WAYS TO PLAY
Refer to letter on toy parts and contents
page to help with assembly.
INSTRUCTIONS
CRISS CROSS CRASH
™
DTN42 DOM I/S SIZE:A5X4 COLOR: 1C+1C
©
2016 Mattel DTN42-1100875524
1 1
2
2
1
2
1 2
C
B
x 4
x 4 x 4
x 3
LABEL SHEET
ATTACH EACH PART AT CONNECTOR LOCATIONS AS SHOWN.
SLIDE TRACK CONNECTOR TO THE CENTER.
NOT FOR USE WITH SOME HOT WHEELS
®
VEHICLES.
CAR PARKING ZONE
ADJUST IF NECESSARY
TO STABILIZE THE SET.
INCLUDES 1 VEHICLE. ADDITIONAL VEHICLES SOLD SEPARATELY.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE
REFERENCE AS THEY CONTAIN IMPORTANT INFORMATION.
A
TRACK SHOULD GO OUTSIDE
THE TABS AT LOCATIONS AS
SHOWN.
TRACK SHOULD GO INSIDE
THE TABS AS LOCATIONS AS
SHOWN.
3
NUMBER CORRESPONDS WITH NUMBERS IN ILLUSTRAION BELOW.
BLUE x2
ORANGE x2
3
CONNECT TRACK SUPPORT TO
TRACK CONNECTOR AT
LOCATIONS AS SHOWN.
B
C
C
C
A
B
B
B
B
C
B
C
C
C
B
B
C
A
B
C
B
A
B
B
O=OFF
I =ON
I
O
POWER ON.
3
1
CAR PARKING ZONE
1
1
1
1
2
2
2
2
3
3
3
3
BLUE
ORANGE
ORANGE
BLUE
2
1
LOAD CARS ON LAUNCH RAMP
TO START THE ACTION!
WIPE OUT IN THE CRASH ZONES!
2
Participe da conversa sobre este produto
Aqui você pode compartilhar o que pensa sobre Hot Wheels DTN42 Criss Cross Crash Pista de corrida. Se você tiver alguma dúvida, primeiro leia atentamente o manual. A solicitação de manual pode ser feita através do nosso formulário de contato.