Manual FERM GGM1002 Pistola de colar

Manual

EN

3

Ferm

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the

wall outlet.

Using extension cables

Only use an approved extension cable suitable for

the power input of the machine. The minimum

conductor size is 1.5 mm

2

. When using a cable

reel always unwind the reel completely.



Always observe the safety instructions

and applicable regulations.

This glue gun (kit) has been especially designed

for glueing products such as wood, plastic, foam,

rubber, fabric, cardboard, tiles, ceramics, etc.

Quickly setting, the glue is perfect for repairing

carpets, bookbinding, fixing soles, etc. The glue is

waterproof and resistant to the action of many

liquids. The glue gun is quick, environmentally-

friendly, energy-saving and together with the glue

facilitates and quickens any job.

Due operating the glow gun

• The normal setting time of the hot glue is 30

seconds. After 30 seconds the glue starts to

set. Having applied the glue on the relevant

surfaces, wait 15 - 20 seconds before joining

them.

• After about 1 minute the joint has reached

90% of its adhesive strength.

• The setting time can be extended to 50 to 60

seconds by applying the glue in thick drops or

shortened by applying the glue in short, fine

lines.

• Joining large surfaces is difficult, as the glue

tends to set before the entire surface has been

covered with glue.

• Preheating the surfaces to be joined

guarantees a strong joint. Sun rays have the

same impact.

• The glue melts from a temperature of approx.

140°C and must never be used on material

that is sensitive to heat.

• The glue gun can be used to replace nails,

paper tape, liquid glue, but not for heavy-duty

jobs.

• The electric glue gun features accurate

temperature control. It is fitted with a special

design feed system that ensures no glue is left

behind inside the mechanism.

• The glue gun requires Ø 11.2 mm glue

cartridges.

• The glue gun comes standard with a bracket

that enables you to put the gun safely on the

table when it is not used.

Operation

• Plug in the tool.

• Insert a glue cartridge into the gun, two when

using it for the first time.

• Wait 5 minutes for the glue to heat.

• Squeeze the trigger to release the glue.

• Replace the glue cartridge as soon as you

notice little if any glue is released from the

gun.

• Disconnect the tool if you do not intend to use

it for some time.

Replacing the nozzle

• Loosen the orange nozzle.

• Fit the nozzle on the glue gun.

Before removing the nozzle, allow the

glue gun to cool down completely to

avoid injuries. Always disconnect the

tool.



Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate over

a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Always disconnect the tool before

cleaning and maintenance work. Never

use inflammable liquids to clean the tool.

Use a brush to clean the glue gun.

• Keep the nozzle clean. Check before every

use there is no glue left on the nozzle.

• Remove any glue left inside the nozzle with a

pin.



Should the machine fail to function correctly, a

number of possible causes and the appropriate

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu FERM GGM1002 Pistola de colar. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com FERM. Eles podem fornecer um manual original. Você está procurando o manual do seu FERM GGM1002 Pistola de colar em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para FERM Pistolas de colar
Mais manuais de Pistolas de colar

Perguntas frequentes sobre FERM GGM1002 Pistola de colar

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

FERM GGM1001 Pistola de colar

Manual

FERM GGM1004 Pistola de colar

Manual

Ryobi R18GLU-0 Pistola de colar

Manual

Parkside IAN 307134 Pistola de colar

Manual

Würth HKP 300-E Pistola de colar

Manual

Parkside IAN 297286 Pistola de colar

Manual

Parkside IAN 291780 Pistola de colar

Manual

Bosch Gluey Pistola de colar

Categorias relacionadas