Manual FERM CSM1019 Serra circular

Manual

Ferm 53

Using extension cables

Only use an approved extension cable suitable for the

power input of the machine. The minimum conductor

size is 1.5 mm

2

. When using a cable reel always unwind

the reel completely.

BEFORE USING THE CIRCULAR SAW:

• Check the following points:

• does the voltage of the motor correspond with the

mains voltage (appliances for a mains voltage of 230 V

• are the mains lead and the mains plug in a good

condition: solid, without any loose ends or damage;

• is the saw blade missing any teeth or showing

any cracks, it so must be replaced immediately.

• Make sure the blade is secure.

• Use this circular saw to saw only wood, wood-like

products.

• Do not use circular saw blades wich are deformed or

damaged.

• Do not use HSS blades.

• Only use blades meeting the required dimensions, as

well as data and descriptions;

Never apply any blades of which the thickness is

greater than that of the riving knife.

• Do not stop the blade of a circular saw by pressing

the blade from the side.

• Check that the blade guard can freely move and fully

closes.

• Never lock-up the guard in the open position.

• Never put sideward pressure on the blade. This may

cause the blade to break.

• Be careful when cutting wood with knots, nails or

cracks in it and/or dirt on it, as these can cause the

blade to get stuck.

• Never leave the circular saw unattended.

• Use this circular saw to saw only wood or wood-like

products.

USING THE MACHINE:

• Use clamps or a vice to hold the work.

• Never remove wood chips and saw dust that is close

to the saw blade with your hands. If there are small

pieces of wood left between the fixed and the

movable parts, the circular saw will have to be

stopped. The plug needs to be removed from the

socket, before any left piece can be removed.

• Check that the blade is suitable for the spindle speed

of the circular saw. Do not attempt to cut before the

circular saw has reached full speed. Make sure the

circular saw runs without load (i.e. is not in contact

with the work) when you switch it on. The circular

saw must have reached its full speed first.

• Never cut wood that is thicker than the depth of the

saw blade.

• When cutting in wooden walls or floors, check there

is no wiring or piping where you intend to cut.

• Switch off the tool and wait until the blade has

stopped completely before moving the saw away

from the work or putting it down. Hearing

protection should be worn when using circular saw.

SWITCH OFF THE MACHINE IMMEDIATELY

WHEN YOU DISCOVER:

• A defective mains plug or mains lead;

• A defective switch.

• Overheating of the circular saw.

• Smoke or odeur caused by scorched insulation.

3. ASSEMBLY AND

ADJUSTING INSTRUCTIONS

Before adjusting the saw, make sure the plug is

removed from the socket.

SETTING THE SAWING ANGLE (BEVEL)

Fig. B.

• Loosen both knobs (1).

• Rotate the soleplate to the correct position (0° -

45°), and tighten the knobs. The sawing angle (bevel)

can be read on the protractor (2).

FITTING THE RIP FENCE

Fig. B.

• Loosen knob (3).

• Insert the rip fence into the slots provided (4).

• Set the correct cut width and tighten the knob (3).

SETTING THE CUT DEPTH

Fig. C.

• Loosen knob (1).

• Move the soleplate (2) downwards.

• The cut depth of the saw blade can be read off on the

side of the safety guard.

• Tighten the clamping knob (1) once the correct

depth is set.

EXCHANGING OR CLEANING THE SAW

BLADE

Fig. D.

• Next loosen the hexagon screw (3) in the centre of

the saw blade, using the Allen key provided.

• Turn the safety guard to the rear, and hold it there

with the aid of the knob (1).

• Withdraw the retaining ring and the saw blade, and

clean the saw blade, or replace it with a new one.

• Again place the saw blade back on the shaft. Ensure

that the teeth of the saw blade are pointing in the

same direction as the riving knife (4).

• Ensure that the riving knife is set in such a way that

• the gap between it and the toothed wheel rim of the

saw blade does not exceed 5 mm

• and that the toothed wheel does not protrude more

than 5 mm beyond the lower edge of the splitting

wedge.

• The riving knife must always be used except when

cutting into the middle of the workpiece.

• Allow the safety guard to return over the saw blade

by releasing the knob (1).

• Refit the retaining ring (5) and tighten the hexagon

screw firmly once more.

4 Ferm

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu FERM CSM1019 Serra circular. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com FERM. Eles podem fornecer um manual original. Você está procurando o manual do seu FERM CSM1019 Serra circular em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para FERM Serras circulares
Mais manuais de Serras circulares

Perguntas frequentes sobre FERM CSM1019 Serra circular

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

FERM CSM1039 Serra circular

Manual

FERM CSM1012 Serra circular

Manual

FERM CSM1018 Serra circular

Manual

FERM CSM1033 Serra circular

Manual

FERM CSM1030 Serra circular

Manual

FERM CSM1037 Serra circular

Manual

FERM CSM1015 Serra circular

Manual

FERM CSM1028 Serra circular

Categorias relacionadas