Manual FERM AGM1095P Rebarbadora

Manual

5

EN

accessories cannot be adequately guarded or

controlled.

f) Threaded mounting of accessories must

match the grinder spindle thread. For

accessories mounted by flanges, the arbour

hole of the accessory must fit the locating

diameter of the flange. Accessories that do

not match the mounting hardware of the power

tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess

wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped,

inspect for damage or install an undamaged

accessory. After inspecting and installing

an accessory, position yourself and

bystanders away from the plane of the

rotating accessory and run the power tool

at maximum no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping flying debris

generated by various operations. The dust

mask or respirator must be capable of filtrating

particles generated by your operation.

Prolonged exposure to high intensity noise

may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken

accessory may fly away and cause injury

beyond immediate area of operation.

j) Hold the power tool by insulated gripping

surfaces only, when performing an

operation where the cutting accessory may

contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool

“live” and could give the operator an electric

shock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

l) Never lay the power tool down until the

accessory has come to a complete stop.

The spinning accessory may grab the surface

and pull the power tool out of your control.

m) Do not run the power tool while carrying

it at your side. Accidental contact with the

spinning accessory could snag your clothing,

pulling the accessory into your body.

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electrical hazards.

o) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in

turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point

of pinching. Abrasive wheels may also break

under these conditions. Kickback is the result

of power tool misuse and/or incorrect operating

procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a firm grip on the power tool

and position your body and arm to allow

you to resist kickback forces. Always use

auxiliary handle, if provided, for maximum

control over kickback or torque reaction

during start-up. The operator can control

torque reactions or kickback forces, if proper

precautions are taken.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu FERM AGM1095P Rebarbadora. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com FERM. Eles podem fornecer um manual original. Você está procurando o manual do seu FERM AGM1095P Rebarbadora em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para FERM Rebarbadoras
Mais manuais de Rebarbadoras

Perguntas frequentes sobre FERM AGM1095P Rebarbadora

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

FERM AGM1034 Rebarbadora

Manual

FERM AGM1035 Rebarbadora

Manual

FERM AGM1098P Rebarbadora

Manual

FERM AGM1002 Rebarbadora

Manual

FERM AGM1028 Rebarbadora

Manual

FERM AGM1019 Rebarbadora

Manual

FERM AGM1001 Rebarbadora

Manual

FERM AGM1031 Rebarbadora

Categorias relacionadas