Manual Broan HI190I Exaustor

Manual

ENGLISH

The appliance must be installed by a qualified person in compliance with the instructions provided.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Only for hoods equipped with electronic control:

The 4th speed (intensive) is automatically lowered to 3rd speed after 5 minutes of operation to optimise energy consumption.

- If the hood is left on (lights and/or motor), after 10 hours in the absence of commands from the user, it will automatically

switch to OFF condition with all services switched off.

- The Buzzer emits a “beep” each time that a command is set from the keyboard or remote control (optional).

- In the event of interruption of power during the hood, if you restore the hood in the OFF state, then the engine must

be reactivate manually.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard.

DESCRIPTION

The hood may be installed in the filtering or the ducting version.

In the Filtering version the air and the kitchen fumes that are conveyed by the apparatus are depurated by

the charcoal filters and put back into the room through the small grilles of the ventilation flue (Fig. 1).

ATTENTION: When using the filtering version, a charcoal filters and an air baffle (Fig. 1A) must be used, which

placed at the top of the structure, allows the air to recycle back into the room.

In the Ducting version, cooking vapours and odours are conveyed straight outside by a disposal duct which

passes through the ceiling (Fig. 2).

INSTALLATION

ATTENTION: Three people are required for proper installation; the unit should be installed by a qualified

operator. Also follow carefully each step of the assembly instructions, and once installation has been

completed, make sure that the hood is firmly secured in place.

To facilitate installation, before starting remove the grease filters: press inward on the clamp at the handle and

pull the filter downward (Fig. 3).

For assembling it is essential to: – Prepare the electrical connection and the air exhaust pipe (CAUTION! For installation

reasons the pipe must absolutely be flexible) inside the telescopic flue so that they are sufficiently long to reach the lower

flue outlet (Fig. 4). – If your unit is installed in a ducting hood, prepare the air exhaust hole.

When installing ducting hoods, to achieve the best possible conditions use an air exhaust pipe that : is as short

as possible, has a minimum of curves (maximum angle: 90°), is made of a material that complies with the standards (which

vary from nation to nation) and is smooth on the inside. It is also advisable to avoid any drastic changes in pipe section

(diameter: 150 mm).

ASSEMBLING - Using the special drilling template, drill the holes for fixing to the ceiling on the vertical side of

your hob. Carefully observe all the indications for final positioning of the apparatus. Take into account that one of

the template axes must correspond to the axis of the hood controls. Fix the bracket to the ceiling using the screws

and screw anchors provided (Fig. 5). Be careful, because the position of the bracket determines the final position

of the apparatus.

Ducting version: Fix the upper flue to the bracket by means of the four screws provided (Fig. 6), with the grilles facing

down, then take the lower flue and insert it in the upper one (Fig. 7). Adjust the height of the flues with the eight retaining

screws (Fig. 7A) taking into account that the hood is 110 mm high and that the distance between the hood and the

hob must be at least 650 mm (Fig. 8).

Take the flange with the metal valve (Fig. 9H) and assemble it onto the opening of the hood for air venting, pressing slightly.

Now make the electrical connection A and connect the air exhaust pipe to the flange B holding the hood raised (Fig.10).

Lift the island and rest it against the lower flue, then fix the parts with the 10 screws provided (Fig. 11). At this point

the installation is complete and the grease filters can be remounted.

Filtering version: After fitting the bracket to the ceiling, install the baffle (Fig. 12) with the four screws “A”; fix the flange

“B” with a rotating movement. Arrange the power cable and the air exhaust pipe as shown in Figure 13. Repeat the

installation from the first point of the ducting version bearing in mind that the upper flue must have the grilles facing up.

CHARCOAL FILTER/S (A) - Fig. 16: one or more charcoal filters are required in the filtering version. If they are

not yet installed in the hood, fit them inside the grease filter (M). Charcoal filters are not required In the ducting version.

If they are already installed in the hood remove them together with the relative filter retainers.

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Broan HI190I Exaustor. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Broan. Eles podem fornecer um manual original. Você está procurando o manual do seu Broan HI190I Exaustor em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Broan Exaustores
Mais manuais de Exaustores

Perguntas frequentes sobre Broan HI190I Exaustor

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.