Manual Bort BAB-12-P Berbequim

Manual

7

GB

Cordless drill/driver

INTENDED USE

• This tool is intended for drilling in wood, metal, ceramic

and plastic; tools with electronic speed control and left/

right rotation are also suitable for screwdriving and thread

cutting

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 Switch for on/off and speed control

2 Switch for changing direction of rotation

3 Keyless chuck

4 Ring for torque control

SAFETY

WARNING! Read all instructions. Failure to follow all instruc-

tions listed below may result in electric shock, fi re and/or seri-

ous injury.

• Ensure the switch is in the off position before inserting

battery pack. Inserting the battery pack into power tools that

have the switch on invites accidents.

• Recharge only with the charger specifi ed by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fi re when used with

another battery pack.

• Use power tools only with specifi cally designated battery

packs. Use of any other battery packs may create a risk of

injury and fi re.

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before you

start working

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the charger (chargers

with a rating of 230V or 240V can also be connected to a

220V supply)

• In case of electrical or mechanical malfunction, immediately

switch off the tool or unplug charger from power source

• SBM Group can assure fl awless functioning of the tool only

when original accessories are used

• Use only accessories with an allowable speed matching at

least the highest no-load speed of the tool

• This tool should not be used by people under the age of

16 years

• Be careful not to drill or drive into areas where electrical

wires may be contacted

• Ensure that switch

is in the middle (locking) position

before making any adjustments or changing accessories as

well as when carrying or storing the tool

• Do not touch the contacts in the charger

• Do not expose tool/charger/battery to rain

• Never charge battery outdoors

• Store tool/charger/battery in locations where temperature

will not exceed 40°C or drop below 0°C

• Batteries will explode in fi re, so do not burn battery for any

reason

• When damaged, and under extreme usage and temperature

conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly

with soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, fl ush eyes with clean water for

a minimum of 10 minutes and seek immediately medical

attention

• When battery is not in tool or charger, it should be kept

away from metal objects such as nails, screws, keys etc. to

prevent short-circuit

• Do not use charger when damaged; take it to one of the

offi cially registered SBM Group Service Stations for a safety

check

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries with

the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire in

the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut off the cord of the charger,

it must be disposed of safely and not left unattended

To ensure longer service life and proper

performance of the battery, take the following

actions when you start using new battery:

1. Use the new battery, without recharging it, till its complete

discharge.

2. Then charge the battery for 3-5 hours.

3. Repeat abovementioned actions (1 and 2) 3-5 times to

reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when carry-

ing out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth, prefer-

ably after each use. Keep the ventilation slots free from dust

and dirt.If the dirt does not come off use a soft cloth moistened

with soapy water. Never use solvents such as petrol, alcohol,

ammonia water, etc. These solvents may damage the plastic

parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please contact

your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during transport,

it is delivered in a sturdy packaging. Most of the packaging

materials can be recycled. Take these materials to the appro-

priate recycling locations. Take your unwanted machines to

your local SBM Group dealer. Here they will be disposed of in

an environmentally safe way.

NiCd batteries can be recycled. Deliver them to a disposal site for

chemical waste so that they can be recycled or disposed of in an

environmentally friendly manner.

English

Avaliação

Mais sobre este manual

Entendemos que é bom ter um manual em papel para o seu Bort BAB-12-P Berbequim. Você sempre pode baixar o manual em nosso site e imprimi-lo você mesmo. Se desejar um manual original, recomendamos que entre em contato com Bort. Eles podem fornecer um manual original. Você está procurando o manual do seu Bort BAB-12-P Berbequim em outro idioma? Escolha o seu idioma preferido em nossa página inicial e pesquise o número do modelo para ver se o temos disponível.

Especificações

Todos os manuais para Bort Berbequins
Mais manuais de Berbequins

Perguntas frequentes sobre Bort BAB-12-P Berbequim

Nossa equipe de suporte pesquisa informações úteis e respostas a perguntas frequentes sobre produtos. Se você encontrar algum dado incorreto em nossas perguntas frequentes, informe-nos usando nosso formulário de contato.

Produtos relacionados

Manual

Bort BAB-10.8N-Li Berbequim

Manual

Bort BAB-14.4U-LiK Berbequim

Manual

Bort BAB-14-DZK Berbequim

Manual

Bort BSM-250 Berbequim

Manual

Skil 3070 DA Berbequim

Manual

Skil 3018 HD Berbequim

Manual

Skil 3000 CA Berbequim

Manual

Skil 3018 RC Berbequim

Categorias relacionadas